Bharat Sanchar Nigam Ltd
When a piece of copper and another of germanium are cooled from room temperature to 800 K then the
resistance of -
a) Each of them increases
b) Each of them decreases
c) Copper increases and germanium decreases
d) Copper decreases and germanium increases
When a signal of 10 mV at 75 MHz is to be measured then which of the following instrument can be used -
a) VTVM
b) Cathode ray oscilloscope
c) Moving iron voltmeter
d) Digital multimeter
When a sample of germanium and silicon having same impurity density are kept at room temperature then –
a) Both will have equal value of resistivity
b) Both will have equal value negative resistivity
c) Resistivity of germanium will be higher than that of silicon
d) Resistivity of silicon will be higher than that of germanium
When an RC driving point impedance function has zeros at s= -2 and s=-5 then the admissible poles for the function would be –
a) s = 0; s = -6
b) s = 0; s = -3
c) s = 0; s = -1
d) s = -3; s = -4
For the n-type semiconductor with n = Np and p = , the hole concentration will fall below the intrinsic value because some of the holes –
a) drop back to acceptor impurity states
b) drop to donor impurity states
c) Virtually leave the crystal
d) recombine with the electrons
The location of lighting arrestor is –
a) Near the transformer
b) Near the circuit breaker
c) Away from the transformer
d) None
Time constant of an RC circuit increases if the value of the resistance is –
a) Increased
b) Decreased
c) Neither a nor b
d) Both a and b
Telemetering is a method of –
a) Counting pulses sent over long distances
b) Transmitting pictures from one place to another
c) Transmitting information concerning a process over a distance
d) None
When the gauge factor of a strain gauge is 2, stress is 1050 kg/cm2, Y = 2.1´ 106 kg/cm2 and R is
100 ohms then the value of DR will be –
a) 2W
b) 3W
c) 4W
d) 1W
As the drain voltage is increased for a junction FET in the pinch off region then the drain current –
a) Becomes zero
b) Abruptly decreases
c) Abruptly increases
d) Remains constant
11. One of the following, which is not a transducer in the true sense, is –
a) Thermocouple
b) Piezoelectric pick up
c) Photo-Voltaic cell
d) LCD
When a transistor is required to match a 100W signal source with a high impedance output circuit then the connection that would be used is –
a) Common base
b) Common collector
c) Common emitter
d) Emitter follower
In a JFET gates are always –
a) forward biased
b) reverse biased
c) unbiased
d) none
The main factor which differentiate a DE MOSFET from an E only MOSFET is the absence of –
a) insulated gate
b) electrons
c) channel
d) P-N junction
An SCR conducts appreciable current when –
a) Anode and gate are both negative with respect to cathode
b) Anode and gate are both positive with respect to cathode
c) Anode is negative and gate is positive with respect to cathode
d) Gate is negative and anode is positive with respect to cathode
Silicon is not suitable for fabrication of light emitting diodes because it is -
a) An indirect band gap semiconductor
b) A direct band gap semiconductor
c) A wide band gap semiconductor
d) A narrow band gap semiconductor
An average responding rectifier type electronic ac voltmeter has its scale calibrated in terms of the rms value of a sine wave, when a square wave voltage of peak magnitude 100V is measured using this voltmeter then the reading indicated by the meter, will be –
a) 111V
b) 100V
c) 90.09V
d) 70.7V
When a four terminal T network is inserted between a source and load resistance as shown in figure then the resistance seen by the source remain the same with or without the four terminal block when R is –
a) 5W
b) 10 W
c) 15 W
d) 20 W
19. In the ac bridge shown in the given figure, the value of Rx and Cx at balance will be –
Which one of the following conditions for Z parameters would hold for a two port network containing linear bilateral passive circuit elements –
a) Z11 = Z22
b) Z12Z21 = Z11Z22
c) Z11Z12 = Z22Z21
d) Z12 = Z21
When the transmission parameters of the following network are A = C = 1, B = 2 and D = 3 then the value of Zin is –
c) 3W
d) 4W
The value of G12 or for the circuit shown in the fig. is –
The two port network of the fig. shown has open circuit impedance parameters given by matrix –
In the circuit shown, the switch closes at t = 0. The voltage across 4mF capacitor in ideal condition changes to –
a) 0
b) 16V
c) 15V
d) 24V
While calculating Rth, constant current sources in the circuit are –
a) replaced by opens
b) replaced by 'shorts'
c) treated in parallel with other voltage sources
d) converted into equivalent voltage sources
Maxwell's loop current method of solving electrical networks –
a) uses branch currents
b) utilizes kirchhoff's voltage law
c) is confined to single-loop circuits
d) is a network reduction method
A transmission line of characteristic impedance Z0 = 50 ohms, phase velocity Vp = 2 x 108 m/s and length l = 1m is terminated by a load ZL= ( 30 – j 40 ) ohms. The input impedance of the line for a frequency of 100 MHz will be
a)(30 + j40 ) ohms
b)( 30 – j40 ) ohms
c)(50 + j40 ) ohms
d)(50 – j40 ) ohms
For an elliptically polarized wave incident on the interface of a dielectric at the Brewster angle then the reflected wave will be-
a) Elliptically polarized
b) Linearly polarized
c) Right circularly polarized
d) Left circularly polarized
A yagi antenna has a driven antenna-
a) Only
b) With a reflector
c) With one or more directors
d) With a reflector and one or more directors
The number of lobes on each side of a 3l resonant antenna is –
a) 3
b) 6
c) 2
d) 1
The electric field intensity of a Hertizian dipole at a remote point varies as-
Radiation resistance of a half wave folded dipole is -
a) 72 W
b) 144W
c) 288 W
d) 216W
When a carrier wave is modulated at 100% it’s power is increased by -
a)100%
b)150 %
c)50%
d)0%
On a clear sky day, the atmospheric radio noise is strongest -
a) During morning hours
b) Around mid-day
c) During nights
d) In the afternoon
TV broadcasting system in India is as per CCIR -
a) System B
b) System I
c) System M
d) System X
For the safety measurement of the internal resistance of a 25-0-25 mA meter, a laboratory multimeter whose sensitivity is equal to –
a) 1k ohm/volt can be used
b) 10 k ohm/volt can be used
c) 100 k ohm/volt can be used
d) 200 k ohm/volt can be used
In order to measure moisture in wood the most suitable method is –
a) Electrical conduction
b) Electrical – capacitive
c) Absorption of radiation
d) Equilirium- moisture vs humidity
The flow rate of elctrically conducting liquid without any suspended practicle cannot be measured by –
a) turbine flow meters
b) electromagnetic flow meters
c) ultrasonic flow meters
d) thermistor based heat loss flow meters
The most useful transducer for displacement sensing with excellent sensitivity, linearity and resolution is –
a) an incremental encoder
b) an abosolute encoder
c) LVDT
d) a strain gauge
When variable reluctance type techometer has 150 teeth on the rotor & the counter records 13,500 pulses per second then the rotational speed will be–
a) 4800 rpm
b) 5400 rpm
c) 6000 rpm
d) 7200 rpm.
41. On a voltage scale, zero dB m in a 600-ohm system could refer to –
a) 1.732 V
b) 1.0 V
c) 0.7746 V
d) 0.5V
One of the following devices which is required in addition in order to measure pressure using LVDT is-
a) strain gauge
b) pitot tube
c) Bourden tube
d) Rotameter
It is required to measure temperature in the range of 13000 C to 15000 c) The most suitable thermocouple to be used as a transducer would be –
a) chromel - constantan
b) Iron - constantan
c) chromel - alumel
d) platinum- rhodium
In a CSI if frequency of output voltage is f Hz, then frequency of input voltage to CSI is-
a) f
b) 2 f
c) f/2
d) 3 f
Identify the type of chipper in the given circuit
a) Type A chopper
b) Type B chopper
c) Type C chopper
d) Type D chopper
Maximum value of charging resistance in an UJT is associated with-
a) peak point
b) valley point
c) any point between peak and valley
d) after the valley point
Thyristor A has rated gate current of 2A and thyristor B a rated gate current of 100 mA-
a) A is a GTO and B is a conventional SCR
b) B is a GTO and A is a conventional SCR
c) B may operate as a transistor
d) none of the above
In a 3 phase full converter, the output voltage during overlap is equal to-
a) zero
b) source voltage
c) source voltage minus the inductance drop
d) average value of the conducting phase voltages
Mark old the correct statement for Cycloconverters-
a) step-down Cycloconverter (CC) works on natural commutation
b) step up CC requires no forced commutation
c) load commutated CC works on line commutation
d) none of the above
In a 3 phase full converter if load current is I and ripple free, then average thyristor current is-
a)
b)
c)
d)
In the RF amplifier stage cascade (CE-CB) amplifier is used because it gives-
a) Large voltage gain
b) Low output impedance
c) Large isolation between the input and the output
d) None of the above
Silicon diode is less suited for low voltage rectifier operation because-
a) it can withstand high temperature
b) ensures low PIV of the diodes
c) ensures lower values of capacitance in the filter
d) reduces ripple content
An amplifier of class A is that in which -
a) Base is biased to cut – off
b) Ic flows most of the time
c) Ie flows all the time
d) Vc often raises to Vcc
A transistor is in active region when-
a) IB = bIC
b) IC=bIB
c) IC=IE
d) IC=IB
For coupling purposes in RF amplifier a buffer amplifier is used because it provides-
a) Maximum loading and minimum mismatch
b) Minimum loading and minimum mismatch
c) Maximum loading and maximum mismatch
d) Minimum loading and maximum mismatch
. A transistor has CE parameter as hie = 10kW, hre =20 x 10-4 , hse = 100, hoe = 25 ms. The hib for this transistor will be-
a) 100 W
b) 99.01 W
c) 5m W
d) 101kW
An FM radio receiver is tuned to a 90.6 MHz broadcast station. It will receive an image frequency of -
a) 110 MHz
b) 112 Hz
c) 114 MHz
d) 120 MHz
In the given fig RL is shorted out, then VCE will become-
a) OV
b) VCC – IBRB
c) Equal to VCC
d) None of the above
See the circuit shown and choose the correct option –
a) Only red will glow
b) Only green will glow
c) Both red and green will glow
d) Neither red nor green will glow
A dc to dc converter having an efficiency of 80% is delivering 16W to a load) If the converter is generating an output of 200V from an input source of 20V, then the current drawn from the source will be –
a) 0.1A
b) 0.5A
c) 1.0A
d) 10.0A
A transistor is operated as a non-saturated switch to eliminate –
a) storage time
b) turn – off time
c) turn – on time
d) delay time
. The output Y of the circuit in the given figure is –
a) (A + B)C + DE
b) AB + C(D + E)
c) (A + B)C + D + E
d) (AB + C) . DE
Rotors used in a two-phase ac servomotor is –
a) solid iron motor
b) squirrel cage rotor
c) drag cup rotor
d) both b and c
Major advantage of TWT over a klystron lies in its –
a) higher bandwidth
b) higher output
c) higher frequency
d) higher gain
The op-map circuit shown in the given figure can be used for –
a) addition
b) subtraction
c) both addition and subtraction
d) multiplication
The Boolean expression for the shaded area in the given Venn diagram is –
A lag compensator is basically a –
a) high pass filter
b) band pass filter
c) low pass filter
d) band elimination filter
Transfer function T (S) of the system in the given fig is-
The overall transfer function for a unity feedback system is
Mark the correct statement regarding this system
1. Position error constant kp for the system is 4
2. The system type one.
3. The velocity error constant kv for the system is finite.
Select the correct answer using the codes given below-
Codes
a) 1,2 and 3
b) 1 and 2
c) 2 and 3
d) 1 and 3
If the rotor’s resistance and reactance are respectively R and X1 its length and diameter are L and D for two phase a) c) servomotor, then-
In a PID controlles the transfer function G(s) is-
Transfer function can be approximated by the system-
The transfer function of an amplifier is given by
The high 3 db frequency of an amplifier will be approximately-
a) 5850 kHz
b) 585 kHz
c) 5850 Hz
d) 585 Hz
An open loop transfer function is given by
Its – loci will be-
. The output signals amplitudes for 1's and 0's in an ADM transmission systems are –
a) Fixed and the repetition rate is also fixed
b) Fixed but the repetition rate is variable
c) Variable and the repetition rate is also variable
d) Variable but the repetition rate is fixed
Microwave link repeaters are typically 50km apart –
a) Because of atmospheric attenuation
b) Because of Output tube power limitations
c) Because of the earth's curvature
d) To ensure that the applied ac voltage is not excessive
. The amplifier inserted at intervals to amplify the signal and compensate for transmission loss on the cable are called-
a) line amplifier
b) equalizing amplifiers
c) compradors
d) repeaters.
Diversity reception in used to-
a) increase receiver sensitivity
b) improve receiver selectivity
c) overcome degrading effect of fading
d) overcome degrading effect of receiver detuning
Mark out transferred electron device in the following-
a) BARITT dived
b) IMPATT dived
c) Gunn divde
d) Step recovery diode
In the output of a normal monochrome receiver video detector voltages, which are not found, are -
a) syne
b) video
c) sweep
d) sound
The HV anode supply for the picture tube of TV receiver is generated in the-
a) mains transformer
b) vertical output stage
c) horizontal output stage
d) horizontal deflection oscillator
In antenna measurements using two aperture antennas of dimensions D1 and D2 , minimum separation between the two should be (x is free space wavelength of radiation uses)
. The frquency range for satellite broad casting is –
a) 30 MHz – 300MHz
b) 30 MHz – 3 GHz
c) 3 GHz – 30 GHz
d) 30 GHz – 300 GHz
Iris is used to –
a) Over come power loss
b) Over come bending effect
c) Over come mismatch error
d) Over come twist effect
In schotty barrier diode current flows because of –
a) Majority carriers
b) Minority carriers
c) Majority and minority carriers
d) None
. Which antennas are used in microwave communication –
a) long wave antennas
b) Rhombic antennas
c) Parabolaidal antennas
d) All of above
Among translator & time of sight system capacity –
a) Of translator is more
b) Of line of sight is more
c) Having equal capacity
d) No relation such as
No of T-state required for memory read or write operation-
a) 2
b) 3
c) 4
d) 6
89. In data transfer operation which flag get affected)-
a) 3140 flog.
b) carry flog
c) sign flog.
d) none
In flowchart which figure represents process like subroutine-
.
The storage and retrieval of data on stacks should follow sequence-
a) last in first out
b) first in first out
c) random in random out
d) none
. While executing program microprocessor checks INTR line clearing-
a) each instruction
b) after interval of two instruction
c) after a subroutine
d) at the end of program.
93. In which error check technique of data communication 2's complement of all bytes of data is transmitted with data-
a) Even parity
b) odd parity
c) check scans
d) cyclic redundancy
. Program execution hierarchy decides which operator-
a) is most important
b) is used first
c) is fastest
d) operators on largest number
. (375)10 = (----)8
a) 550
b) 557
c) 567
d) 577
To obtain 2048 8 memory using 128 8 memory chip how many IC required-
a) 2
b) 4
c) 8
d) 16
A Decimal no. 17 can be converted in binary, the binary no. will be.-
a) 10001
b) 01110
c)00111
d) 11100
Is the Universal logic gate-
a) AND
b) OR
c) NAND
d) X-OR
A monostable state in multivibrator means-
a) which returns itself to its single stable state
b) the state used only once in circuit
c) the state of circuit can not get changed
d) the state of circuit always changing
For designing binary counter which flip flop is preferred -
a) T FF
b) SR FF
c) D FF
d) JKFF
His handwriting was not ----- so I could not read his note –
a) attractive
b) eligible
c) clear
d) legible
They started to ----- people into the theatre only at six -
a) enter
b) admit
c) follow
d) accept
I told him to buy things that are lasting (Give the appropriate synonym of the underlined word).
a) ending
b) ordinary
c) durable
d) cheap
Give the word which is most opposite in meaning of the word 'evident'-
a) doubtful
b) unimportant
c) disagreed
d) understood
I expressed by disagreement ------ him on that issue-
a) between
b) with
c) about
d) for
‘Sugarbowl’ of the world is -
a) India
b) Cuba
c) Brazil
d) USA
Palk strait separates-
a) India and Srilanka
b) India and Burma
c) Britain and France
d) Malaysia and Sumatra
The minimum number of atoms in a molecule of an element are-
a) 1
b) 5
c) 2
d) 10
Tides in the sea are caused by-
a) Effect of sun
b) Effect of moon
c) combined effect of moon and sun
d) Gravitational, centrifugal and centripetal forces
. The Bar council of India decided to close over law colleges across the country for their failure to maintain minimum teaching standard) There number is
a) 140
b) 200
c) 150
d) 100
Aswan Dam is located in-
a) Egypt
b) Libya
c) Sudan
d) Iran
Ghana Birds sanctuary is in the state of -
a) Rajasthan
b) Madhya Pradesh
c)Uttar Pradesh
d) Maharashtra
Dry ice is-
a) Frozen carbon monoxide
b) Frozen carbon dioxide
c) Frozen ammonia
d) None of these
East flower river of India is -
a) Cauvery
b) sone
c) Narmada
d) Tapti
The total length of the great wall of China is –
a) 1,400 miles
b) 1,500 miles
c) 1,300 miles
d) 1,400 miles
Deficiency of vitamin C may result in-
a) beriberi
b) night blindness
c) dermatitis
d) Scurvy
Bharat Shah a film financer was granted bail by Supreme Court after a period of –
a) 11 months
b) 2 years
c) 18 months
d) 15 months
Indian local time is based on-
a) 800 E longitude
b) E longitude
c) 1100 E longitude
d) 250 E longitude
The two days Shiv Shena Mahashivir of 2002 started at Shirdi on –
a) 9th April 2002
b) 10th April 2002
c) 8th April 2002
d) 11th April 2002
Which one is a good preservative of food?
a) Spirit
b) Formaldehyde
c) Sugar
d) None of the above

Test Paper :9 Paper Type
Test Paper :9
Paper Type : General - other
Posted By : Jai
BSNL GE-JTO Recruitment Examination
Test Paper - VI
At a frequency below the resonant frequency series circuit is-
a.) Inductive
b.) Capacitive
c. )Resistive
d.)None
The electrical conductivity of metals is typically of the order of (Ohm –1 m-1) -
a.) 107
b. )105
c. )10-4
d. )10-6
he output of a piezoelectric crystal has-
a. )Low amplitude and low impedance
b. )High amplitude and high impedance
c. )Low amplitude and high impedance
d.)High amplitude and low impedance
The time constant associated with the capacitor charging in the circuit shown in the given figure is –
a. )6ms
b. )10ms
c. )15ms
d.) 25ms
The Q factor of an inductor would be higher if it is made of –
a.) Thinner wire
b.) Longer wire
c.) Shorter wire
d.) Thicker wire
A cavity resonator can be represented by –
a.) An LC circuit
b.) An LCR circuit
c.) A lossy inductor
d.) A lossy capacitor
Air gap in the iron core of an inductor prevents –
a.) Core saturation
b). Hysterisis loss
c.) Flux leakage
d.) Transformer action
Between the plates of an air capacitor if a glass slab is slipped without moving the plate then -
a.) Its capacitance is decreased
b.) Its capacitance is increased
c.) Its capacitance is hardly affected
d. )Capacitor is discharged
For current to flow, a circuit must be –
a.) Isolated
b). Insulated
c.) Complete
d.) Protected
Human ear can detect sound intensities of the order of –
a.) 10-20 w/m2
b). 10-13 w/m2
c.) 10-6 w/m2
d.) 10-3 w/m2
A FET operates on –
a). Majority carriers only
b). Minority carriers only
c). Positively charged ions only
d.) None
An SCR can conduct for a full half cycle or any part of it –
a. )and continue conduction for other half cycle
b.) but blocks the conduction for other half cycle
c.) nothing can be said
d.) none
In CRT aquadag carries -
a. )aqueous solution of graphite
b. )sweep voltage
c. )secondary emission electrons
d.) none of the above
From the following circuit, in order to obtain a 12-v stabilized supply the input to the terminals A and B
should be -
a.)less than 12v with terminal A positive with respect to terminal B
b. )greater than 12v with B positive with respect to A
c. )less than 12v with A negative with respect to B
d. )greater than 12v with A positive with respect to B
When the value of ICBO in a silicon transistor of b = 49 is 20 Na then the value of ICEO for a temperature rise of 180c would be –
a. )8mA
b. )160 hA
c. )1mA
d. )7.84mA
MOSFET can operate in –
a. )Depletion mode
b. )Enhancement mode
c. )Depletion-only mode
d. )Both a & b
For a circuit design the very factor of an SCR, which is to be taken into account is –
a. )
d.) None
The functions of an oxide layer in an IC device is to –
a.) mask against diffusion or ion implant
b.) insulate the surface electrically
c.) produce a chemically stable protective layer
d.) all the above
One of the following bipolar transistors which has the highest current gain bandwidth product for similar geometry is –
a.) NPN germanium transistor
b.) NPN silicon transistor
c.) PNP germanium transistor
d. )PNP silicon transistor.
With the increasing temperature, the electrical conductivity would –
a.) Increase in metals as well as in intrinsic semiconductors.
b.) Increase in metals but decrease in intrinsic semiconductors.
c. )Decrease in metals but increase in intrinsic semiconductors.
d. )Decrease in metals as well as in intrinsic semiconductors.
For the following circuit, the current X is 3A then the power delivered by the dependent current source D is –
a.) 50 watts
b) 50 watts
c. )1500 watts
d. )15000 watts
The current in resistor R shown in the fig. will be –
a.) 0.2A
b.) 0.4A
c.) 0.6A
d.) 0.8A
In the network shown in the given fig. the capacitor C1 is initially charged to a voltage V0 before the switch S in the circuit is closed. In the steady state-
a.)C1 and C2 are charged to equal voltages
b.) C1 and C2 are charged with equal coulombs
c. )C1 and C2 are discharged fully
d. ) C2 alone is charged to voltage V0
The equivalent circuit of a wire-wound resistor can be represented as –
For the fig. shown the fundamental cutset for the branch 12 is –
a. )2, 1, 5
b. )2, 6, 7, 8
c. )2, 1, 3, 4,5
d. )2, 3, 4
Ideally, attenuator pads should not change –
a. )voltage level
b.) impedance level
c.) power level
d.) voltage, power or impedance level
When the two networks are cascaded through an ideal Buffer and if tr1 and tr2 are the rise times of the two networks, then the overall delay of the two networks together will be –
For the network shown in the following fig. one of the following theorems which can be conveniently used to calculate the power consumed by the 10W resistor is –
a. )Thevenin's theorem
b.) Maximum power transfer theorem
c.) Millman's theorem
d.) Superposition theorem
The nodal analysis is primarily based on the application of –
a. )KVL
b.) KCL
c.) Ohm's law
d.) Both b and c
When the driving point impedance of a network at a frequency of 1Hz is then the impedance can be realised as –
For a lossless line-
1. Series resistance is zero 2. Shunt conductance is zero
3. Shunt conductance is infinite 4. Series resistance is infinite
a. ) 1 & 2
b. )2 & 3
c. ) 2 & 4
d.)3 & 4
When a square wave is fed to an RC circuit then-
a.) Voltage across R is square and across C is not square
b) Voltage across C is not square and across R is not square
c. ) Voltage across both R and C are square
d. )Voltage across both R and C are not square
When an A.M. broadcast radio transmitter radiates 10 kw power when the modulation percentage is 60 then the power of the carrier is-
a. ) 5.00 kw
b.) 7.69 kw
c.) 8.47 kw
d.) 9.17 kw
The main components of atmosphere responsible for absorption of em waves are -
a. ) Nitrogen and Oxygen
b. )Nitrogen and hydrogen
c.) Oxygen and water vapour
d. )Nitrogen and water vapour
The effective height of a linear antenna of length ‘l’ is say ‘x’ when the current distribution along it’s length is uniform and say, it is ‘y’ when the current distribution is sinusoidal then x/y is equal to -
a.) 2
b.) 1
c. ) 4/ p
d.) p/4
In a hollow rectangular waveguide, the phase velocity -
a.) Increases with increasing frequency
b.)Decreases with increasing frequency
c. ) Is independent of frequency
d.)Will vary with frequency depending upon the frequency range
For TM waves in a parallel plate waveguide, the minimum attenuation arising from imperfect conductors would occur at a frequency of (fc is the cut–off frequency )-
a.) 3fc
When a transmission line having 50 impedance is terminated in a load of ( 40 + j30) W then the VSWR is –
a.) j 0.033
b.)0.8 + j 0.6
c.) 1
d.)2
The ionosphere plays a significant role in radio wave propogation at-
a. )High frequencies
b.)Ultra-high frequencies
c. ) Microwave frequencies
d.)Optical frequencies
When a carrier wave is modulated at 100% it’s power is increased by-
a. )100%
b. )150 %
c. )50%
d.) 0%
Reluctances in series are –
a. )Subtractive
b.) Additive
c.) Multiplicative
d.) None.
When the meters X and Y requires 40 mA and 50 mA respectively for full scale deflection then –
a. )X is more sensitive
b.) Y is more sensitive
c. )both are equally sensitive
d.) not possible to determine from the given data.
In the context of ac bridge measurement the term "Wagner Ground" means –
a.) a special RC connection that eliminates stray magnetic effects.
b.) any unwanted and unintended ground connection.
c.) a large metal plate buried in the ground and connected to one corner of the bridge.
d.) a special RC connection that eliminates stray capacitance effects.
The gating and counting circuits of a digital counter –
a. )cannot handle MHz signals
b.) cannot handle GHz signals
c. )can handle GHz signals
d.) none.
De- sauty bridge is more widely used because of –
a. )simplicity
b. )perfect balance for imperfect capacitors
c. )perfect balance for air capacitors
d.) maximum sensitivity.
A schottky diode clamp is used along with a switching BJT for –
a. )reducing the power dissipation.
b. )reducing the switching time
c. )increasing the value of b
d.) reducing the base current.
The phenomenon of creeping occurs in –
a. )Energy meters
b.) Ammeters
c. )Wattmeter
d. )Voltmeters
A permanent magnet moving coil measures the –
a. )true rms value
b.) dc value
c.) peak value
d. )rms plus dc value
49. The D`Arsonval meter movement can be converted into an audio frequency ac ammeter by adding to it a-
a. )thermocouple
b.) rectifier
c.) chopper
d. )transducer
Which one of the following detectors is generally used in ac bridges for audio frequency range ?
a. )Ac voltmeter
b. )CRO
c. )Headphones
d.) Vibration galvanometer.
In single phase circuit capacitor used for power factor correction decreases –
a.) The power factor
b.) The line current
c.) Both a and b
d.) The line current and increases power factor
In the given figure X the balanced bridge should be
style="height: 48236; left: 16; position: absolute; width: 528; z-index: 2; mso-ignore: vglayout; top: 13795; margin-left: 168px; margin-top: 78px">
self-inductance having resistance
b. )A capacitance
c. )A non-Inductive resistance
d. )An inductance and a capacitance in parallel
SiO2 layer in an integrated circuit provides –
a. )Electrical connection to external circuit
b.) Physical strength
c. )Isolation
d. )Conducting path
For an SCR with turn on time of 5 microsecond, an ideal trigger pulse should have-
a. )short rise time with pulse width = 3 m sec
b. )vlong rise time with pulse width = 6 m sec
c. )short rise time with pulse width = 6 m sec
d.)long rise time with pulse width = 3 m sec
In a 3-phase half wave diode rectifier, the ratio of average output voltage to per phase maximum a c voltage is-
a) 0.955
b. )0.827
c.) 1.654
d. )1.169
In multiple pulse modulation used in PWN inverters, the amplitude and frequency for triangular carrier and square reference signals are respectively 4V, 6 KH2 and 1V, 1KH2. The number of pulses per half cycle and pulse width is respectively-.
a. )6, 900
b. )3, 450
c. )4, 600
d.) 3, 400
A four quadrant operation requires-
a. )two full converters in series.
b.) two full converters connected back to back.
c.) two full converters connected in parallel.
d.) two semi converters connected back to back
In voltage source inverters-
a. )load voltage waveform o depends on load impedance z, where as load current waveform io does not depend on z,
b. )Both o and io depend on z,
c.) o does not depend on z where as depends on z
d. )both o and do not depend on z
For an RC driving – point impedance function, the poles and zeros-
a. )should alternate on real axis
b.) should alternate only on the negative real axis
c.) should alternate on the imaginary axis
d.) can lie anywhere on the left half place.
The functions of connecting a resistor in series with gate - cathode circuit and a zener diode across gate cathode circuit are, respectively to protect the gate circuit from-
a.) over voltages, over currents.
b. )over currents over voltages.
c. )over currents, noise signals
d. )noise signals, over voltages.
The plate efficiency of a class C amplifier is high because-
a.) A resonant circuit is used as load
b.) The plate current flows when the instantaneous plate voltage is low.
c. ) The plate current flows only when grid is driven positive
d. )None of the above
The circuit diagram shown in the figure consist of transistor is -
a. ) Parallel connection
b.) Cascode connection
c. ) Darlington connection
d. )Cascade connection
Increase of current in one transistor in a direct coupled circuit -
a. ) Causes an increase in current in other transistors of the circuit
b. )Causes a decrease in current in other transistor
c. )Does not affect the currents of other transistors connected in the circuit
d. )May either increase or decrease currents of other transistors connected in the circuit.
In a PNP transistor the charge carriers in the base region which play an important role in the operation of the transistor are-
a. ) The majority carriers
b.) The minority carriers
c. ) Nothing can be said
d. )None of the above
Voltage gain in a CC amplifier is-
a. )Cannot exceed unity
b. )Is always constant
c. ) Is dependent on input signal
d. )Depends on output impedance
Random-access-memory means –
a. )memory in a random fashion
b. )memory in a zigzag fashion
c. )memory in a circular fashion
d. )memory in a square fashion
BCD code is –
a. )an alphanumeric code
b. )a binary code
c .) the same thing as binary numbers
d. )non-weighed
The transfer function of a system is . The phase swift at w = 0 and w = a will be -
a.) 900 and –00
b. )-900 and 900
c. )-1800 and 1800
d. )None of the above
Number of resolutions in a 8 bit D/A converter is –
a. )8 bit
b.) 4 bit
c. )6 bit
d.) 10 bit
A bistable multivibrator is used as a –
a.) Free running multivibrator
b.) Frequency multiplier
c.) Frequency divider
d. )Wave shaper
The transfer function of a system is The phase shift at w = o and w = will be –
a. )900 and -00
b. )–900 and 900
c. )–1800 and 1800
d. )none of the above.
A forward path transfer function of a unity feedback control system is equal to The unit step response of this system starting from rest will have its maximum value at a time equal to –
a. )0 sec
b. )0.56 sec
c. )5.6 sec
d.) infinity.
To obtain the output position in a position control system, which one of the following transducers is used-
a.) Strain Gauge
b.) Load cell
c. )Synchro
d.) Thermistor
The maximum resonance peak for the second order transfer function T(S) = will be –
a. )4
b. )4/3
c. )2
Considering control system in the given fig .
For slight variation in G, the ratio of open loop sensitivity to closed pool
sensitivity will be given by-
a.) 1: (1+GH)
b.) 1 : (1+GH)-1
c. )1 : (1-GH)
d. )1 : (1-GH)-1
The diversity system in Troposcatter links is made use of to-
a. )Increase the bandwidth
b.) Prevent noise effects
c.) Increase the directivity of the antenna.
d.) Detect signal in the presence of fading.
Mark out wrong statement regarding compandor-
a.) It compresses the higher amplitude parts of a signal before modulation and expands them back to normal again after demodulation.
b.) It gives preferential treatment to the weaker parts of the signal
c.) For weaker signals, it gives a poor ratio of signal strength to quantizing error.
d. )Weaker signals, transverse more quantum steps than they would do otherwise and so quantizing error is reduced
Among other equipment a sub marine cable repeater contains –
a.) A dc power supply and regulator
b. )Filters for the two directions of transmission
c.) Multiplexing and demultiplexing equipment
d.) Pilot inject and pilot extract equipment
In a communication system noice is most likely to affect the signal-
a.) At the transmitter
b.) In the channel
c.) In the information source
d.) At the destination
The given circuit is a –
a.) Monostable multivibrator
b.) Frequency division circuit
c.) Miller sweeps circuit
d.) Bootstrap sweep circuit
In a plane transverse electromagnetic wave-
a.) Angle between electric and magnetic vectors is O.
b.)Angle between electric and magnetic vectors is 900
c.) Angle between electric and magnetic vectors is 1800
d.) None of above.
Directional coupler is a function of-
a.) Two port wave-guide
b.) Four port wove guide
c. )Single port wave-guide
d.) Size port wave-guide.
Isolators are used to couple generator and load because –
a.) It increases power of signal
b.) To match any load with generator
c. )To get phase shifted o/p
d.) To differentiate load & generator
In travelling wave tube for getting amplified output -
a. )Electron beam travels and RF field remains stationary
b.) Both electron beam and RF field travels in same direction
c. )Both electron beam and RF field remains stationary
d.) RF field travels and electron beam remains stationary
Crystal diode works on principle of –
a. )Negative resistance
b. )Positive resistance
c. )Square low
d.) Linear impedance
In gunn effect oscillator which mode having lowest operating frequency –
a. )Domain mode
b. )Delayed domain mode
c. )Quenched domain mode
d. )LSA mode
In Reflex klystron maximum energy transferred to gap by electrons-
a. )eR
b. )ee
c. )el
d. )eR , ee, el
The radio waves get absorbed by atmosphere depends –
a.) Their distance from transmitter is long
b.) Wave power is weak
c. )Improper polarization of wave
d.) Frequency of waves
8085 mP has no of sets of communication lines-
a. )2
b.) 3
c.) 4
d. ) None
No. of o/p ports in peripheral mopped I/p are up to-
a.) 32
b.) 64
c. ) 128
d.) 256
Is two byte instruction-
a.) MOV A, B
b.) ANA B
c.) MV I B, 92 H
d.) LHLD 2050 H
Banch instructions-
a. ) only uses flogs setting to make decision.
b. )only sets flogs according to results.
c. ) uses flogs settings as well as sets flogs setting
d. )nighteruse flog settings not set flogs.
What will be the time delay achieved from following loop-
Loop DCX B 6
MOV A, C, 4
ORA B 4
JNZ Loop 10
system clock freg. = 2 MHz.
a. ) 10 m s
b.)12 m s
c.) 14 m s
d. )16 m s
After execution of pop statement-
a. ) Stack pointer decremented by 2
b.) Stack pointer incremented by 2
c.) Stack pointer decremented by 1
d. )Stack pointer incremented by 1
Labels are used as an alternative for-
a.) Data
b.) Register name
c.) Memory address
d) Stack pointer
Microprogramming is a technique-
a) For programming the microprocessor
b.) For writing small programs efficiently
c. )For programming the control steps of computer
d.) For programming o/p / i/p
00110010 – 01000101 =?
a.) 00010011
b. )11101101
c. )11100011
d. )11100100
When an array is possed as an argument to a function what exactly gets possed-
a.) Address of the array
b. )Values of elements of array
c.) Number of elements of array
d. )Address of the first element of the array
A write cycle time means-
a.) Minimum length of write pulse
b.) Minimum amount of time for which data must be valid before write pulse end
c.) Minimum time required between successive write operation
d.) Minimum time for which data must be valid after write pulse ends
If three i/p of a gate are 1, 0, 1 then output is O the gate must be-
a.) NOT
b.) AND
c.) OR
d. )NAND.
Inverting amplifier configuration using operational amplifier is –
Which logic family is most faster-
a.) ECL
b.) DCTL
c.) RTL
d) TTL
For getting positive o/p from two i/p OR gate for positive logic-
a.) both i/p must be positive
b.) both i/p must be negative
c.) any one of i/p must be positive
d.) undefined condition
Supercilious is –
a. )Harighty
b.) High brow
c.) Angry
d.) Inane.
Give the synonym of 'moribund'-
a.) Undertaking
b.) Burial
c.) Leather bound
d.) Dying
The convention was to end on May 13 with a month long break in between. What do the two prepositions indicate?
a.) Duration
b.) Time
c) Direction
d.) Position
According to the writer what influences our dreams-
a. )inner censorships
b.) the stories
c. )the tales
d) none.
Vaunted is –
a.) Unvanquished
b.) Fell.
c.)Belittled
d.) Exacting.
The sun rays falls vertically on -
a.) Tropics
b.) Doldrums
c.) Poles
d.) Equator
Trimurti is associated with -
a.) Ellora
b.) Ajanta
c.) Khajuraho
d.) Elephant caves
n which year did the congress adopt “Poorna Swaraj” or complete independence as its goal?
a.) 1930
b.) 1929
c.) 1928
d.) 1942
Director of CBI-
a.) D.C Sharma
b.) A. M Shrivastava
c.) P.C Sharma
d.) P.C Dole
Rajiv Gandhi khel Ratna award for the year 2001 goes to -
a.) P. gopichand
b.) P. T Usha
c.) Sachin Tendulkar
d.) Gurpreet Singh
During which time is vist to Mecca treated as Haj?
a.) Id-Ul-Fitr
b) Id-ul-Zuha
c. )Milad-un-Nabi
d.) Any time
Of the 109 known metals, how many occur in nature and how many are produced synthetically in particle accelerators!
a.) 79 and 10
b.) 80 and 29
c. )95 and 14
d.) None can be produced synthetically
Earth’s average speed per second around the sun is -
a.) 30 km
b. ) 32 km
c.) 34 km
d.) 35 km
Governor of Reserve Bank of India is -
a.) Bimal Jalan
b.) C. Ranga Rajan
c. )Rana Malhotra
d. )S. Venkata Ramanan
The first pope to enter a mosque in Damascus syria is -
a )Pope John Paul II
b.) Pope John Paul I
c.) Pope John Paul III
d. )Pope John Paul V
Uranium is found in the state of -
a.) Orissa
b.) A. P
c.) Karnataka
d. )Bihar
Nuclear Power plant in Pakistan is located at-
a. )Karachi
b.) Peshawar
c. )Ellipse
d.) Paraboloid
Post new comment