Bharat Sanchar Nigam Ltd
When a piece of copper and another of germanium are cooled from room temperature to 800 K then the
resistance of -
a) Each of them increases
b) Each of them decreases
c) Copper increases and germanium decreases
d) Copper decreases and germanium increases
When a signal of 10 mV at 75 MHz is to be measured then which of the following instrument can be used -
a) VTVM
b) Cathode ray oscilloscope
c) Moving iron voltmeter
d) Digital multimeter
When a sample of germanium and silicon having same impurity density are kept at room temperature then –
a) Both will have equal value of resistivity
b) Both will have equal value negative resistivity
c) Resistivity of germanium will be higher than that of silicon
d) Resistivity of silicon will be higher than that of germanium
When an RC driving point impedance function has zeros at s= -2 and s=-5 then the admissible poles for the function would be –
a) s = 0; s = -6
b) s = 0; s = -3
c) s = 0; s = -1
d) s = -3; s = -4
For the n-type semiconductor with n = Np and p = , the hole concentration will fall below the intrinsic value because some of the holes –
a) drop back to acceptor impurity states
b) drop to donor impurity states
c) Virtually leave the crystal
d) recombine with the electrons
The location of lighting arrestor is –
a) Near the transformer
b) Near the circuit breaker
c) Away from the transformer
d) None
Time constant of an RC circuit increases if the value of the resistance is –
a) Increased
b) Decreased
c) Neither a nor b
d) Both a and b
Telemetering is a method of –
a) Counting pulses sent over long distances
b) Transmitting pictures from one place to another
c) Transmitting information concerning a process over a distance
d) None
When the gauge factor of a strain gauge is 2, stress is 1050 kg/cm2, Y = 2.1´ 106 kg/cm2 and R is
100 ohms then the value of DR will be –
a) 2W
b) 3W
c) 4W
d) 1W
As the drain voltage is increased for a junction FET in the pinch off region then the drain current –
a) Becomes zero
b) Abruptly decreases
c) Abruptly increases
d) Remains constant
11. One of the following, which is not a transducer in the true sense, is –
a) Thermocouple
b) Piezoelectric pick up
c) Photo-Voltaic cell
d) LCD
When a transistor is required to match a 100W signal source with a high impedance output circuit then the connection that would be used is –
a) Common base
b) Common collector
c) Common emitter
d) Emitter follower
In a JFET gates are always –
a) forward biased
b) reverse biased
c) unbiased
d) none
The main factor which differentiate a DE MOSFET from an E only MOSFET is the absence of –
a) insulated gate
b) electrons
c) channel
d) P-N junction
An SCR conducts appreciable current when –
a) Anode and gate are both negative with respect to cathode
b) Anode and gate are both positive with respect to cathode
c) Anode is negative and gate is positive with respect to cathode
d) Gate is negative and anode is positive with respect to cathode
Silicon is not suitable for fabrication of light emitting diodes because it is -
a) An indirect band gap semiconductor
b) A direct band gap semiconductor
c) A wide band gap semiconductor
d) A narrow band gap semiconductor
An average responding rectifier type electronic ac voltmeter has its scale calibrated in terms of the rms value of a sine wave, when a square wave voltage of peak magnitude 100V is measured using this voltmeter then the reading indicated by the meter, will be –
a) 111V
b) 100V
c) 90.09V
d) 70.7V
When a four terminal T network is inserted between a source and load resistance as shown in figure then the resistance seen by the source remain the same with or without the four terminal block when R is –
a) 5W
b) 10 W
c) 15 W
d) 20 W
19. In the ac bridge shown in the given figure, the value of Rx and Cx at balance will be –
Which one of the following conditions for Z parameters would hold for a two port network containing linear bilateral passive circuit elements –
a) Z11 = Z22
b) Z12Z21 = Z11Z22
c) Z11Z12 = Z22Z21
d) Z12 = Z21
When the transmission parameters of the following network are A = C = 1, B = 2 and D = 3 then the value of Zin is –
c) 3W
d) 4W
The value of G12 or for the circuit shown in the fig. is –
The two port network of the fig. shown has open circuit impedance parameters given by matrix –
In the circuit shown, the switch closes at t = 0. The voltage across 4mF capacitor in ideal condition changes to –
a) 0
b) 16V
c) 15V
d) 24V
While calculating Rth, constant current sources in the circuit are –
a) replaced by opens
b) replaced by 'shorts'
c) treated in parallel with other voltage sources
d) converted into equivalent voltage sources
Maxwell's loop current method of solving electrical networks –
a) uses branch currents
b) utilizes kirchhoff's voltage law
c) is confined to single-loop circuits
d) is a network reduction method
A transmission line of characteristic impedance Z0 = 50 ohms, phase velocity Vp = 2 x 108 m/s and length l = 1m is terminated by a load ZL= ( 30 – j 40 ) ohms. The input impedance of the line for a frequency of 100 MHz will be
a)(30 + j40 ) ohms
b)( 30 – j40 ) ohms
c)(50 + j40 ) ohms
d)(50 – j40 ) ohms
For an elliptically polarized wave incident on the interface of a dielectric at the Brewster angle then the reflected wave will be-
a) Elliptically polarized
b) Linearly polarized
c) Right circularly polarized
d) Left circularly polarized
A yagi antenna has a driven antenna-
a) Only
b) With a reflector
c) With one or more directors
d) With a reflector and one or more directors
The number of lobes on each side of a 3l resonant antenna is –
a) 3
b) 6
c) 2
d) 1
The electric field intensity of a Hertizian dipole at a remote point varies as-
Radiation resistance of a half wave folded dipole is -
a) 72 W
b) 144W
c) 288 W
d) 216W
When a carrier wave is modulated at 100% it’s power is increased by -
a)100%
b)150 %
c)50%
d)0%
On a clear sky day, the atmospheric radio noise is strongest -
a) During morning hours
b) Around mid-day
c) During nights
d) In the afternoon
TV broadcasting system in India is as per CCIR -
a) System B
b) System I
c) System M
d) System X
For the safety measurement of the internal resistance of a 25-0-25 mA meter, a laboratory multimeter whose sensitivity is equal to –
a) 1k ohm/volt can be used
b) 10 k ohm/volt can be used
c) 100 k ohm/volt can be used
d) 200 k ohm/volt can be used
In order to measure moisture in wood the most suitable method is –
a) Electrical conduction
b) Electrical – capacitive
c) Absorption of radiation
d) Equilirium- moisture vs humidity
The flow rate of elctrically conducting liquid without any suspended practicle cannot be measured by –
a) turbine flow meters
b) electromagnetic flow meters
c) ultrasonic flow meters
d) thermistor based heat loss flow meters
The most useful transducer for displacement sensing with excellent sensitivity, linearity and resolution is –
a) an incremental encoder
b) an abosolute encoder
c) LVDT
d) a strain gauge
When variable reluctance type techometer has 150 teeth on the rotor & the counter records 13,500 pulses per second then the rotational speed will be–
a) 4800 rpm
b) 5400 rpm
c) 6000 rpm
d) 7200 rpm.
41. On a voltage scale, zero dB m in a 600-ohm system could refer to –
a) 1.732 V
b) 1.0 V
c) 0.7746 V
d) 0.5V
One of the following devices which is required in addition in order to measure pressure using LVDT is-
a) strain gauge
b) pitot tube
c) Bourden tube
d) Rotameter
It is required to measure temperature in the range of 13000 C to 15000 c) The most suitable thermocouple to be used as a transducer would be –
a) chromel - constantan
b) Iron - constantan
c) chromel - alumel
d) platinum- rhodium
In a CSI if frequency of output voltage is f Hz, then frequency of input voltage to CSI is-
a) f
b) 2 f
c) f/2
d) 3 f
Identify the type of chipper in the given circuit
a) Type A chopper
b) Type B chopper
c) Type C chopper
d) Type D chopper
Maximum value of charging resistance in an UJT is associated with-
a) peak point
b) valley point
c) any point between peak and valley
d) after the valley point
Thyristor A has rated gate current of 2A and thyristor B a rated gate current of 100 mA-
a) A is a GTO and B is a conventional SCR
b) B is a GTO and A is a conventional SCR
c) B may operate as a transistor
d) none of the above
In a 3 phase full converter, the output voltage during overlap is equal to-
a) zero
b) source voltage
c) source voltage minus the inductance drop
d) average value of the conducting phase voltages
Mark old the correct statement for Cycloconverters-
a) step-down Cycloconverter (CC) works on natural commutation
b) step up CC requires no forced commutation
c) load commutated CC works on line commutation
d) none of the above
In a 3 phase full converter if load current is I and ripple free, then average thyristor current is-
a)
b)
c)
d)
In the RF amplifier stage cascade (CE-CB) amplifier is used because it gives-
a) Large voltage gain
b) Low output impedance
c) Large isolation between the input and the output
d) None of the above
Silicon diode is less suited for low voltage rectifier operation because-
a) it can withstand high temperature
b) ensures low PIV of the diodes
c) ensures lower values of capacitance in the filter
d) reduces ripple content
An amplifier of class A is that in which -
a) Base is biased to cut – off
b) Ic flows most of the time
c) Ie flows all the time
d) Vc often raises to Vcc
A transistor is in active region when-
a) IB = bIC
b) IC=bIB
c) IC=IE
d) IC=IB
For coupling purposes in RF amplifier a buffer amplifier is used because it provides-
a) Maximum loading and minimum mismatch
b) Minimum loading and minimum mismatch
c) Maximum loading and maximum mismatch
d) Minimum loading and maximum mismatch
. A transistor has CE parameter as hie = 10kW, hre =20 x 10-4 , hse = 100, hoe = 25 ms. The hib for this transistor will be-
a) 100 W
b) 99.01 W
c) 5m W
d) 101kW
An FM radio receiver is tuned to a 90.6 MHz broadcast station. It will receive an image frequency of -
a) 110 MHz
b) 112 Hz
c) 114 MHz
d) 120 MHz
In the given fig RL is shorted out, then VCE will become-
a) OV
b) VCC – IBRB
c) Equal to VCC
d) None of the above
See the circuit shown and choose the correct option –
a) Only red will glow
b) Only green will glow
c) Both red and green will glow
d) Neither red nor green will glow
A dc to dc converter having an efficiency of 80% is delivering 16W to a load) If the converter is generating an output of 200V from an input source of 20V, then the current drawn from the source will be –
a) 0.1A
b) 0.5A
c) 1.0A
d) 10.0A
A transistor is operated as a non-saturated switch to eliminate –
a) storage time
b) turn – off time
c) turn – on time
d) delay time
. The output Y of the circuit in the given figure is –
a) (A + B)C + DE
b) AB + C(D + E)
c) (A + B)C + D + E
d) (AB + C) . DE
Rotors used in a two-phase ac servomotor is –
a) solid iron motor
b) squirrel cage rotor
c) drag cup rotor
d) both b and c
Major advantage of TWT over a klystron lies in its –
a) higher bandwidth
b) higher output
c) higher frequency
d) higher gain
The op-map circuit shown in the given figure can be used for –
a) addition
b) subtraction
c) both addition and subtraction
d) multiplication
The Boolean expression for the shaded area in the given Venn diagram is –
A lag compensator is basically a –
a) high pass filter
b) band pass filter
c) low pass filter
d) band elimination filter
Transfer function T (S) of the system in the given fig is-
The overall transfer function for a unity feedback system is
Mark the correct statement regarding this system
1. Position error constant kp for the system is 4
2. The system type one.
3. The velocity error constant kv for the system is finite.
Select the correct answer using the codes given below-
Codes
a) 1,2 and 3
b) 1 and 2
c) 2 and 3
d) 1 and 3
If the rotor’s resistance and reactance are respectively R and X1 its length and diameter are L and D for two phase a) c) servomotor, then-
In a PID controlles the transfer function G(s) is-
Transfer function can be approximated by the system-
The transfer function of an amplifier is given by
The high 3 db frequency of an amplifier will be approximately-
a) 5850 kHz
b) 585 kHz
c) 5850 Hz
d) 585 Hz
An open loop transfer function is given by
Its – loci will be-
. The output signals amplitudes for 1's and 0's in an ADM transmission systems are –
a) Fixed and the repetition rate is also fixed
b) Fixed but the repetition rate is variable
c) Variable and the repetition rate is also variable
d) Variable but the repetition rate is fixed
Microwave link repeaters are typically 50km apart –
a) Because of atmospheric attenuation
b) Because of Output tube power limitations
c) Because of the earth's curvature
d) To ensure that the applied ac voltage is not excessive
. The amplifier inserted at intervals to amplify the signal and compensate for transmission loss on the cable are called-
a) line amplifier
b) equalizing amplifiers
c) compradors
d) repeaters.
Diversity reception in used to-
a) increase receiver sensitivity
b) improve receiver selectivity
c) overcome degrading effect of fading
d) overcome degrading effect of receiver detuning
Mark out transferred electron device in the following-
a) BARITT dived
b) IMPATT dived
c) Gunn divde
d) Step recovery diode
In the output of a normal monochrome receiver video detector voltages, which are not found, are -
a) syne
b) video
c) sweep
d) sound
The HV anode supply for the picture tube of TV receiver is generated in the-
a) mains transformer
b) vertical output stage
c) horizontal output stage
d) horizontal deflection oscillator
In antenna measurements using two aperture antennas of dimensions D1 and D2 , minimum separation between the two should be (x is free space wavelength of radiation uses)
. The frquency range for satellite broad casting is –
a) 30 MHz – 300MHz
b) 30 MHz – 3 GHz
c) 3 GHz – 30 GHz
d) 30 GHz – 300 GHz
Iris is used to –
a) Over come power loss
b) Over come bending effect
c) Over come mismatch error
d) Over come twist effect
In schotty barrier diode current flows because of –
a) Majority carriers
b) Minority carriers
c) Majority and minority carriers
d) None
. Which antennas are used in microwave communication –
a) long wave antennas
b) Rhombic antennas
c) Parabolaidal antennas
d) All of above
Among translator & time of sight system capacity –
a) Of translator is more
b) Of line of sight is more
c) Having equal capacity
d) No relation such as
No of T-state required for memory read or write operation-
a) 2
b) 3
c) 4
d) 6
89. In data transfer operation which flag get affected)-
a) 3140 flog.
b) carry flog
c) sign flog.
d) none
In flowchart which figure represents process like subroutine-
.
The storage and retrieval of data on stacks should follow sequence-
a) last in first out
b) first in first out
c) random in random out
d) none
. While executing program microprocessor checks INTR line clearing-
a) each instruction
b) after interval of two instruction
c) after a subroutine
d) at the end of program.
93. In which error check technique of data communication 2's complement of all bytes of data is transmitted with data-
a) Even parity
b) odd parity
c) check scans
d) cyclic redundancy
. Program execution hierarchy decides which operator-
a) is most important
b) is used first
c) is fastest
d) operators on largest number
. (375)10 = (----)8
a) 550
b) 557
c) 567
d) 577
To obtain 2048 8 memory using 128 8 memory chip how many IC required-
a) 2
b) 4
c) 8
d) 16
A Decimal no. 17 can be converted in binary, the binary no. will be.-
a) 10001
b) 01110
c)00111
d) 11100
Is the Universal logic gate-
a) AND
b) OR
c) NAND
d) X-OR
A monostable state in multivibrator means-
a) which returns itself to its single stable state
b) the state used only once in circuit
c) the state of circuit can not get changed
d) the state of circuit always changing
For designing binary counter which flip flop is preferred -
a) T FF
b) SR FF
c) D FF
d) JKFF
His handwriting was not ----- so I could not read his note –
a) attractive
b) eligible
c) clear
d) legible
They started to ----- people into the theatre only at six -
a) enter
b) admit
c) follow
d) accept
I told him to buy things that are lasting (Give the appropriate synonym of the underlined word).
a) ending
b) ordinary
c) durable
d) cheap
Give the word which is most opposite in meaning of the word 'evident'-
a) doubtful
b) unimportant
c) disagreed
d) understood
I expressed by disagreement ------ him on that issue-
a) between
b) with
c) about
d) for
‘Sugarbowl’ of the world is -
a) India
b) Cuba
c) Brazil
d) USA
Palk strait separates-
a) India and Srilanka
b) India and Burma
c) Britain and France
d) Malaysia and Sumatra
The minimum number of atoms in a molecule of an element are-
a) 1
b) 5
c) 2
d) 10
Tides in the sea are caused by-
a) Effect of sun
b) Effect of moon
c) combined effect of moon and sun
d) Gravitational, centrifugal and centripetal forces
. The Bar council of India decided to close over law colleges across the country for their failure to maintain minimum teaching standard) There number is
a) 140
b) 200
c) 150
d) 100
Aswan Dam is located in-
a) Egypt
b) Libya
c) Sudan
d) Iran
Ghana Birds sanctuary is in the state of -
a) Rajasthan
b) Madhya Pradesh
c)Uttar Pradesh
d) Maharashtra
Dry ice is-
a) Frozen carbon monoxide
b) Frozen carbon dioxide
c) Frozen ammonia
d) None of these
East flower river of India is -
a) Cauvery
b) sone
c) Narmada
d) Tapti
The total length of the great wall of China is –
a) 1,400 miles
b) 1,500 miles
c) 1,300 miles
d) 1,400 miles
Deficiency of vitamin C may result in-
a) beriberi
b) night blindness
c) dermatitis
d) Scurvy
Bharat Shah a film financer was granted bail by Supreme Court after a period of –
a) 11 months
b) 2 years
c) 18 months
d) 15 months
Indian local time is based on-
a) 800 E longitude
b) E longitude
c) 1100 E longitude
d) 250 E longitude
The two days Shiv Shena Mahashivir of 2002 started at Shirdi on –
a) 9th April 2002
b) 10th April 2002
c) 8th April 2002
d) 11th April 2002
Which one is a good preservative of food?
a) Spirit
b) Formaldehyde
c) Sugar
d) None of the above

Test Paper :11 Paper Type
Test Paper :11
Paper Type : General - other
Posted By : Admin
BSNL PAPER
When a inductive coil connected to a 200 V, 50Hz ac supply with 10A current flowing through it dissipates 1000 watts then which of the following will have least value in ohms-
a.) Resistance
b.) Reactance
c.) Impedance
d.) None
Oscillator crystal are made of –
a.) Silicon
b.) Germanium
c.) Quartz
d.) None
For small size, high frequency coils, the most common core material is-
a. )Air
b. )Ferrite
c.) Powdered ion
d.) Steel
If we have a parallel plate capacitor of plate area 'A' and plate separatoin t and having a capacity C and a metallic plate r of area A and of negligible thickness is introduced in the capacitor at a distance from either of the two plates as shown in the given figure then the capacity of the capacitor will become –
a.)
b.) C
c.) 2C
d.) 4C
A superconductor is a –
a.) A material showing perfect conductivity and Meissner effect below a critical temperature
b.) A conductor having zero resistance
c.) A perfect conductor with highest di-magnetic susceptibility
d.) A perfect conductor which becomes resistance when the current density through it exceeds a critical value
When an inductor tunes at 200 KHz with 624 pF capacitor and at 600 KHz with 60.4 pF capacitor then the self capacitance of the inductor would be –
a) 8.05 pF
b) 10.05pF
c.) 16.01pF
d.) 20.01pF
Sparking occur when a load is switched off because the circuit has high –
a.) Inductance
b.) Capacitance
c.) Resistance
d.) None
Sparking between contacts can be reduced by inserting a –
a.) Resistance in the line
b.) Capacitor in series with contacts
c.) Capacitor in parallel with contacts
d.) None
RF amplifier of an A.M. receiver is normally biased in –
a.) Class 'A'
b.) Class 'b'
c.) Class 'C'
d.) None
The value of gate voltage for the operation of enhancement of only N channel MOSFET has to be –
a.) High positive
b.) High negative
c.) Low positive
d.) Zero
The input gate current of a FET is –
a.) a few microamperes
b.) negligibly small
c.) a few milliamperes
d.) a few amperes
In the following fig. with R = 30k, the value of current through 2 K resistor is –
a.) 25 mA
b.) 40 mA
c.) 25/16 mA
d.) 10 mA
A step recovery diode –
a.) has on extremely short recovery time
b.) conducts equally well in both directions
c.) is mainly used as a harmonic generator
d.) is an ideal rectifiers of high frequency signals
In order to get maximum undistorted output signal from CE amplifier with VCC 10V, the value of VCE (Q) should be approximately-
a.) 0.1V
b.) 5V
c.) 10V
d) V
In a FET the electrode, which corresponds to collector in bipolar transistor, is –
a.) source
b.) drain
c.) gate
d.) none
The device which acts like an NPN and a PNP transistor connected base to base and emitter to collector is –
a.) Triac
b.) UJT
c.) Diac
d.) SCR
A typical optical fibre has –
a.) High refractive index core and low refractive index cladding
b.) Low refractive index core and high refractive index cladding
c.) Both a and b
d.) None
In the following figure circuit diagram of an op-amp based is shown. The ratio is equal to –
a.) 9
b.) 11
c.) 10
d.) 21
When a loud speaker is connected across the terminals A and B of the network shown in the fig. then its impedance to obtain maximum power dissipation in it will be –
a.) 3 – j1
b.) 3 + j9
c.) 7.5 + j 2.5
d.) 7.5 – j 2.5
In the lattice network, the value of R for the maximum power transfer to the load –
a.) 5
b.) 6.5
c.) 8
d.) 9
For a lossy transmission line short circuited at the receiving end, the input impedance is given by (Z0 is the characteristic impedance, Ö is the propagation constant and l is the length of the line-
a.) Z0 cot h Öl
b.) Z0 cot Öl
c.) Z0 tan h.Ö l
d.) Z0 tan Öl
The approximate thickness of the radome wall should be –
a.) l
b.) l/4
c.) l/2
d.) l/8
A relatively permanent information is stored in
a. ) ROM
b.) RAM
c.) PROM
d.) Volatile memory
The rise time of the RC network shown in the given figure is approximately equal to –
b.) RC
c.) 2RC
d.) 4RC
If in the network shown in the fig. initially a steady state is attained by closing the switch 's' and then if the switch is opened at t = 0, then the current i(t) through the inductor will be –
a.) cos50tA
b.) 2A
c.) 2cos100tA
d.) 2sin50tA
When the p network of figure – I and T-network of figure – II are equivalent then the values of R1, R2 and R3 will be respectively –
a) 9W, 6W and 6W
b.) 6W, 6W and 9W
c.) 9W, 6W and 9W
d.) 6W, 9W and 6W
When the impedance matrices of a two port networks are given by and , then if these two networks are connected in series then the impedance matrix of the resulting two-port network will be –
d.) indeterminate
Joule/coulomb is the unit of -
a.) Electric field potential
b.) Potential
c .) Charge
d.) None of the above
The electric field line and equipotential lines-
a.) Are parallel to each other
b.)Are one and same
c.) Cut each other orthogonally
d.)Can be inclined to each other at any angle
For a lossy transmission line short circuited at the receiving end, the input impedance is given by (When Z0 is the characteristic impendence g is the propagation constant and L is the length of the line
When two equal positive point charges are placed along X- axis at X1 and –X1 respectively then the electric field vector at a point P on the positive Y-axis will be directed-
a.) In the +x direction
b.) In the –x direction
c. ) In the +y direction
d.) In the –y direction
The directions of and in TEM mode transmission line with respect to the direction of propagation are-
a.) Both and are transverse to the direction of propagation
b.) is and are transverse and h has a component in the direction of propagation
c.) is entirely transverse and has a component in the direction of propagation
d. ) is entirely transverse and has a component in the direction of propagation
The lowest TM mode in a rectangular waveguide of cross –section a x b with a>b will be-
a.) TM01
b.)TE10
c.) TM112
d.)TE11
When a transmitter in a free space radiates a mean power of ‘p’ watts uniformly in all directions then at a distance d sufficiently far from the source in plane the electric field E should be related to p and d as –
. When a dipole antenna was radiating with some excitation in free space radiating a certain amount of the power v if then this antenna is immersed in a lake where water is non-dissipative but has a dielectric constant of 81, then the radiated power with the same excitation will be
a.) Decrease to finite non-zero value
b.)Remain the same
c. )Increase
d.)Decrease to zero
When a (75 – j40)W load is connected to a coaxial line of Z0 = 75 W at 6MHz then the load matching on the line can be accomplished by connecting-
a.) A short – circuited stub at the load
b.)An inductance at the load
c. )A short circuited stub at a specific distance from the load
d.)none of the above
As compared to analog multimeters, digital multimeters are –
a.) less accurate
b.) more accurate
c.) equally accurate
d.) none.
When a signal of 10 mV at 75 MHz is to be measured then which of the following instruments can be used –
a.) VTVM
b.) Cathode ray oscilloscope
c.) Moving iron voltmeter
d.) Digital multimeter
Which of the following statement is true about two wattmeter method for power measurement in three phase current ?
a.) power can be measured using two wattmeter method only for star connected three phase circuits.
b.) when two meter show indentical readings, in the power factor is 0.5.
c.) when power factor is unit, one of the wattmeter reads zero
d.) when the reading of the two wattmeters are equal but of opposite sign, then the power factor is zero –
When a capacitance transducer has two plates of area 5cm2 each, separated by an air gap of 2mm than the displacement sensitivity in pf/cm due to gap change would be –
a.) 11.1
b.) 44.2
c.) 52.3
d.) 66.3
The Q of a radio coil –
a.) is independent of frequency
b.) increases monotonically as frequency increases
c.) decreases monotonically as frequency increases
d.) increases upto a certain frequency and then decreases beyond that frequency
When a generator of internal impedance and operating at 1GHz feeds a load via a coaxial line of characteristic impedance 50 ohm then the voltage wave ratio on the feed line is –
a.) 0.5
b.) 1.5
c.) 2.5
d.) 1.75
The coding system typically used in digital telemetry is –
a.) PPM (pulse position modulation)
b.) PAM (pulse amplitude modulation)
c.) PCM (pulse code modulation)
d.) PDM (pulse duration modulation)
Radiation pyrometers are used for the measurement of temperature in the range of –
a.) -2000C to 5000C
b.) 00C to 5000C
c.) 5000C to 12000C
d.) 12000C to 25000C
In the given figure band structure is shown. It is of –
a.) Gallium Avesenide (GaAs)
b.) Silicon (Si)
c.) Copper (Cu)
d.) Germanium (Ge)
When anode is positive with respect to cathode in an SCR, the numbers of blocked p-n junction is –
a.) 1
b.) 2
c.) 3
d.) 4
The circuit symbol for a GTO is
a. b.
c. d.
In the given fig. mark out the type of Cyclo converters
a.) 1 phase to 1 phase with continuous conduction
b.) 1 phase to 1 phase with discontinuous conduction
c.) step up device
d.) 3 phase to 1 phase device
In the given fig. A-1, C=5, m H and C=20 m F, C is initially charged to 200 V. After the switch.
S is closed at t = 0 the
maximum value of current and the
time at which it reaches this value are respectively.
a.) 400 A, 15.707 mS
b.) 50 A, 30 mS
c.) 100 A, 62.828 mS
d.) 400 A, 31.414 mS
50. In the given circuit the maximum current in the main SCR M can be-
a.) 200 A
b.) 170.7 A
c.) 141.4 A
d.) 70.7 A
The transfer function of an amplifier is given by
The high 3-db frequency of the amplifier will approximately
a.) 5850 KHZ
b.)585 KHZ
c.) 5850 HZ
d.)585HZ
In comparison to full wave rectifier with two diodes the four divide bridge rectifier has the dominant advantage of -
a). Higher current carrying
b.)Lower ripple factor
c.) Higher efficiency
d.)Lower peak increase voltage require
Power output increase in a class-c amplifier-
a.) If the conduction angle decrease
b).If the conduction angle increase
c.) Are not governed by the conduction angle
d.)None of the above
A transistor with hie = 1.5 k and hfe = 75 is used in an emitter follower circuit where R1 and R2 are used for normal biasing . Approximate value of it’s current amplification is-
a.)75
b.)76
c.)75/76
d.)-75
Amplifier of class B has high theoretical efficiency of 78.5 percent because-
a.) It is biased almost to saturation
b.)Its quiescent current is low
c.)It’s output is an exact replica of it’s input
d.)It is biased well below cut off
The coupling that produces minimum interference with frequency response is-
a.) Direct coupling
b.)Impedance coupling
c.) R C coupling
d.)Transformer coupling
In the circuit shown in the given figure Rf provides
a.) Current series feedback
b.)Current shunt feedback
c.) Voltage series feedback
d.)Voltage shunt feedback
Mark the correct relation for the junction transistor
Data in the serial form can be converted into parallel form by using –
a.) PISO shift register
b.) SOIP shift register
c.) SIPO shift register
d.) POIS shift register
PROMs are used to store-
a.) bulk information
b.) information to be accessed rarely
c.) sequence information
d.) relatively permanent information
The horizontal axis in a 3 bit unipolar D/A converter represents-
a.) Output bit combination
b.) analog output voltage
c.) input bit combination
d.) none of the above
'Not allowed' condition in NAND gate SR flip flop is –
a.) s = 0, R = 0
b.) s = 1, R = 1
c.) s = 0, R = 1
d.) s = 1, R = 0
Name the fastest logic family-
a) TTL
b.) RTL
c.) DCTL
d.) ECL
Equation corresponding to De Morgan's theorem in Boolean Algebra is –
a.) (A+B) (A+B) = AA + AB + BA + BB
c.) A + AB = A
d.) None of the above
In the given fig find radix of the system –
a.) 2
b.) 4
c.) 6
d.) 8
Modems are used for data transmission telephone lines to –
a.) increase the transmission capacity
b) improve noice performance
c.) incorporate error control coding
d.) eliminate dc component in the transmitted signal
The figure of a control system is shown. The maximum value of gain K for which the system is stable is-
a.)
b.) 3
c.) 4
d.) 5
Identify the example of open-loop system-
a.) A windscreen wiper
b.) Aqualung
c.) Respiratory system of an animal
d.) A system for controlling Anti-rocket missiles.
Consider the following expressions indicating the step or impulse response of an initially relaxed control system-
1. (5 – 4e-2+) u(t)
2. (e-2t +5) (u(t))
3 .V(t) + 8e-2t u(t)
4 . V(t) + 4e-2t 4(t)
Those which correspond to the step and impulse response of the same system include-
a.) 1&3
b.) 1&4
c.) 2&4
d.) 1&4
A system is described by
To test its stability by Lyapunov’s method the following V functions are considered.
Mark the most suitable V-function in this case-
a.) Only V1
b.) Only V2
c.) Both V1 and V2
d.) Neither V1 nor v2
Identity the polar plot of a typical type zero system with open loop transfer function
The scattering matrix of a magic –tee shown in the given figure is-
Which is the following relate to rational transfer function of a system-
1. Ratio of Fourier transform of output to input with zero initial conditions.
2. Ratio of Laplace transform of output to input with zero initial conditions.
3. Laplace transform of system impulse response.
4. Laplace transform of system unit step response select the correct answer using the codes given below.
Codes
a.) 1 and 4
b.) 2 and 3
c.) 1 and 3
d.) 2 and 4
For the signal g (t) – 10 cos (50 pt) cos2 (150at)
The Nyquist sampling state in t seconds is
a.) 150 samples per second
b.) 200 samples per second
c.) 300 samples per second
d.) 350 samples per second
In the case of a 70 MHz 1F carries for a transponder band width of 36 MHz; energy must lie between – MHz.
a.) 34 and 106
b.) 52. And 88
c.) 106 and 142
d.) 34 and 142
Radar used to eliminate clutter in navigational application is –
a.) Pulse radar
b.) Tracking radar
c.) MTI radar
d.) Mono pulse radar
The 1.55 mm windows is not yet in use with fiber optic systems because –
a.) The attenuation is higher than at 0.85 mm
b) The attenuation is higher than at 1.3mm
c.) Suitable laser devices have not yet been developed
d.) It does not lend itself to wavelength multiplexing
Pre-emphasis in FM systems involves-
a.) Compression of the modulating signal
b.) Expansion of the modulating signal
c.) Amplification of lower frequency components of the modulating signal.
d.) Amplification of higher frequency components of the modulating signal.
In a terrestrial microwave system transmission of signals is achieved through-
a.) reflection from the ionosphere
b.) line of sight mode
c) reflection from the ground
d.) diffraction from the stratosphere.
Casse grain feed is used with a parabolic reflector to
a.) increase the gain of the system
b). increase the bandwidth of the system
c.) reduce the size of the main reflector
d.) allow the feed to be placed at a convenient point.
In most microwave communication link rain drop attenuation is caused due to-
a.) scattering of microwaves by water drops of specific size.
b) scattering of microwaves by a collection of droplets acing as a single body.
c.) absorption of microwaves by water and consequent heating of the liquid
d.) absorption of the microwaves by water vapor in the atmosphere.
Circuit in the given figure represents. –
a.) an astable multivibrator
b.) A monostable multivibrator
c.) Voltage controlled oscillator
d.) Ramp generator
. . D = r is-
a.) Maxwell's 1st equation
b.) Maxwell's II equation
c.) Maxwell's III equation
d.) Maxwell’s IV equation
In a rectangular wave-guide which TM mode exists-
a.) TM00
b.) TM01
c.) Tm10
d.) TM11
In directional coupler a portion of power two velliry fram port 1) to port 2) is coupled to.
a). port 4
b). port 3
c.) port 2.
d.) port 3 & 4.
For high power i.e. 10 w to 50 kw measurement –
a.) Barometer are used
b.) Thermisters are used
c.) Calorimetric technique
d.) Calorimetric watt meter technique used
The difference between TWT & klystron is –
a.) In TWT electrons are in contact with RF field for long time & in klystron for short time
b.) In klystron electrons are in contact with RF field for long time & in TWT for short time
c.) In klystron there is no contact in RF field & electrons while in TWT there is contact
d.) In TWT phase is no contact is RF field & electrons while in klystron there is contact
Which one is most suitable for transmission through wave guide-
a.) Hown antennas
b.) Bioconical antennas
c.) helical antenna
d. )Discone
The skip distance of microwave is given by –
a.)
b. )
c.)
d.)
How many general purpose registers 8085mp-
a.) 4
b.) 6
c.) 8
c.) 10
8085 mP has no. of addressing modes-
a.) 2
b.) 3
c.) 4
d.) 5
What will be status of z and c y flag after execution of SUB A instruction
a.) z = 0, cy = 0
b.) z = 0, cy = 1
c.) z = 1, cy = 0
d.) z = 1, cy = 1
Microprocessor accept interrupt only if.
a.) interrupt flip flop disabled.
b.) when INTA signal is low.
c. ) interrupt flip flop enabled.
d.) none of above.
Microprogramming is a technique
a.) for programming the microprocessor
b.) for writing small programs efficiently
c.) for programming the control steps of computer
d.) for programming o/p / i/p
High level programs like C are converted into machine language with the help of
a.) interpreter
b.) compiler
c.) operating
d.) system
(10110011)2 = (?)8
a.) 253
b.) 263
c.) 273
d.) 283
A Not gate at the output of AND gate converts AND gate into-
a.) NAND
b.) NOR
c.) AND
d.) NOPE.
The O/P of a logic gate is the gate must be-
a.) AND
b.) OR
c.) NAND
d.) X-OR
A symbol of JK flip flop is-
A demultiplener-
a.) has multiple i/p and single o/p
b.) has multiple i/p and multiple o/p
c.) has multiple i/p and multiple o/p
d.) has single i/p and single o/p
. Which of the following best describes the authour`s attitude toward fairy tales ?
a.) fascination
b.) open approval.
c.) Indulgent tolerance.
d.) Scornful.
What type of sentence is this ?
Hurray! We won the match
a.) Exclamatory
b.) assertive
c.) Negative
d.) Affirmative
Before which of the following word will you put 'a'
a.) hour
b.) M. A.
c.) Umbrella
d.) Man
The noun form of 'fresh' is –
a.) freshly
b.) freshen
c.) fresheners
d.) fresh itself
The word 'clang' is an example of –
a.) Simile
b.) inversion
c.) onomatopoeia
d.) irony
The Forbes magazine acclaimed Azim Premji as richest India's is the chairman of-
a.) Pentafour software
b) Infosys
c.) IBM
d.) Wipro
Bharat Ratna award for the year 2001 goes to-
a.) Lata Mangeshkar and Zakeer Hussain
b.) Zakeer Hussain and Bismillah Khan
c.) Bismillah Khan and Lata Mangeshkar
d.) Lata Mangeshkar and Ustad Amzad Ali Khan
Mr. George W-Bush takes over as ------ President of the united states of America succeeding Mr. Bill Clinton-
a.) 42nd
b.) 43rd
c.) 40th
d.) 45th
New Chief Minister of Pondicherry is-
a.) T. Venkat Naidu
b.) K. Hari Harh
c.) N. Rengaswany
d.) M. Mudliar
No court has the jurisdiction to interfere with the election process once set in motion by the Election commission. This is enshrined in Article-
a.) 311
b.) 329
c.) 356
d.) 365
Ostrich is a-
a.) Running bird
b.) Flying bird
c) Swimming bird
d.) Migratory bird
The main atmospheric gas responsible for green house is-
a.) Oxygen
b.) Nitrogen
c.) Ozone
d.) Carbon-dioxide
Which of the following is not a Kharif Crop-
a.) Rice
b.) groundnut
c.) Sugarcane
d.) gram
The function of World Bank is to-
a.) Help in reconstruction and development of world economy
b.) Facilitate poor countries to trade on concessional rates
c.) Promote growth of international trade and equilibrium in balance of payments
d.) Ease trade barriers and establish rule of fair trade
Speed of sound is maximum in-
a. )Water
b.) Air
c.) Steel
d.) Vacuum
“Long years ago we made a trust with destiny.” Whose words are these-
a.) Subhash Chandra Bose
b.) Jawaharlal Nehru
c.) Lajpat Rai
d.) Bhagat Singh
Durand cup is associated with-
a.) Hockey
b.) Tennis
c.) Football
d.) Badminton
Rabindranath Tagore was awarded the Nobel Prize in literature in the year.
a.) 1908
b.) 1910
c.) 1913
d.) 1914
India successfully conducted its first underground nuclear experiment at Pokhran in Rajas than on-
a.) May 18, 1975
b.) May 20, 1974
c) May 17, 1974
d.) May 17, 1974
An emergency loan of $ 500 million to help reconstruct infrastructure in earth quake devastated Gujarat approved by-
a.) Asian development Bank
b.) World Bank
c.) Swiss Bank
d.) Reserve Bank of India
Post new comment